使用多槽手動超聲波清洗機能夠?qū)Ω鞣N工件進行快速高能效的清洗，很多人工沒有辦法清洗干凈的縫隙、孔洞，都能在多槽手動超聲波清洗機中得到有效清潔，所以現在這種超聲波清洗設備廣受應用。那么怎樣才能讓多槽手動超聲波清洗機清洗的更加干凈呢？

The use of multi-slot manual ultrasonic cleaning machine can clean various workpieces quickly and efficiently. Many gaps and holes that cannot be cleaned manually can be effectively cleaned in the multi-slot manual ultrasonic cleaning machine. Therefore, this ultrasonic cleaning equipment is widely used now. So how can we make the multi-slot manual ultrasonic cleaner cleaner cleaner?

1、使用品質好的純水

1. Use high-quality pure water

如果想讓多槽手動超聲波清洗機達到更好的清洗效果，那么就要注意外接的純凈水能否達到要求的純度，因為超聲波清洗機在作業時，對電導率和電阻都有一定的要求，而水質的純度不同，其電導率和電阻也都會不一樣，所以為了提高清洗的潔凈度要注意清洗機中使用的純水品質良好。

If you want to achieve better cleaning effect for the multi-slot manual ultrasonic cleaner, you should pay attention to whether the external purified water can reach the required purity, because the ultrasonic cleaner has certain requirements for conductivity and resistance when it is operating, and the conductivity and resistance will vary with the purity of water, so in order to improve the cleanliness of cleaning, you should pay attention to the good quality of pure water used in the cleaner.

2、頻率的選擇要合適

2. The selection of frequency should be appropriate

多槽手動超聲波清洗機清洗工件就是通過超聲波發出的頻率讓清洗液產生空化效應，從而加速溶解和剝離被清洗工件上灰塵、油脂等污垢，所以選擇合適的超聲波頻率也能提高清洗的效果。例如，使用水或水清洗劑時由空化作用引起的物理清洗力需要使用低頻超聲波；對小間隙、狹縫、深孔的零件清洗高頻超聲波效果更好。

The multi-slot manual ultrasonic cleaning machine cleans the workpiece by using the frequency of ultrasonic wave to make the cleaning fluid produce cavitation effect, thus accelerating the dissolution and stripping of dust, grease and other dirt on the cleaned workpiece. Therefore, selecting the appropriate ultrasonic frequency can also improve the cleaning effect. For example, when using water or water cleaning agent, the physical cleaning force caused by cavitation needs to use low-frequency ultrasound; High-frequency ultrasonic cleaning is better for parts with small gaps, narrow slots and deep holes.

3、清洗液劑量要適中

3. The dosage of cleaning fluid should be moderate

一般清洗液液面高于振動子表面0.5米以上為佳，由于多槽手動超聲波清洗機受駐波場的影響，波節處振幅很小，波幅處振幅大，所以為了避免造成清洗不均勻，應該注意使用合適的清洗液劑量，并將清洗物品位置應放在波幅處，這樣清洗效果就會更好。

Generally, the liquid level of cleaning solution is better than 0.5m above the surface of the vibrator. Due to the influence of the standing wave field, the amplitude at the wave node is very small, and the amplitude at the wave amplitude is large. Therefore, in order to avoid uneven cleaning, attention should be paid to the use of appropriate cleaning solution dose, and the cleaning items should be placed at the wave amplitude, so that the cleaning effect will be better.

此外用多槽手動超聲波清洗機清洗工件要注意槽液不能加的太滿，以免發生兩槽超聲波清洗劑之間相互混合以及瀝干時清洗筐底部粘液的現象。此外，多槽手動超聲波清洗機的每個槽應為獨立的操作工序，注意不要將兩槽清洗劑相互串用或人為減少操作工序以及清洗的操作時間。

In addition, when cleaning the workpiece with a multi-slot manual ultrasonic cleaner, pay attention that the tank liquid should not be too full, so as to avoid the phenomenon of mutual mixing between the two tanks of ultrasonic cleaner and the mucus at the bottom of the cleaning basket when draining. In addition, each tank of the multi-slot manual ultrasonic cleaning machine should be an independent operation process. Pay attention not to use the cleaning agents of the two tanks in series or reduce the operation process and cleaning time manually.

通常在清洗時每道工序的時間定為三至五分鐘，如果被清洗物品的表面積比較大，或者工件的結構較為復雜時，要注意根據實際情況酌情調整多槽手動超聲波清洗機的清洗時間。若被清洗物容易出現重疊以及粘附的現象，那么在將被清洗物放入及取出槽液的時候可以抖動一下工件，讓清洗劑充分與工件接觸以提高清洗效果。

Generally, the time of each process is set at three to five minutes during cleaning. If the surface area of the cleaned object is large or the structure of the workpiece is complex, the cleaning time of the multi-slot manual ultrasonic cleaning machine should be adjusted according to the actual situation. If the object to be cleaned is prone to overlap and adhesion, the workpiece can be shaken when the object to be cleaned is put into and taken out of the tank liquid, so that the cleaning agent can fully contact the workpiece to improve the cleaning effect.

使用以上幾種方法就能夠有效提高多槽手動超聲波清洗機的清洗潔凈度，大家在使用多槽手動超聲波清洗機的時候就要多注意。此外，每一種型號的超聲波清洗機都有著一定的差別，所以，在實際的應用過程中大家應該注意按照超聲波清洗機的操作說明書來清洗。關注我們http://m.chendakeji.cn，了解更多相關事項！

Using the above methods can effectively improve the cleaning cleanliness of the multi-slot manual ultrasonic cleaner. You should pay more attention when using the multi-slot manual ultrasonic cleaner. In addition, each type of ultrasonic cleaner has certain differences, so in the actual application process, everyone should pay attention to cleaning according to the operating instructions of the ultrasonic cleaner. Follow us http://m.chendakeji.cn , learn more about relevant matters!