高壓去毛刺清洗機工藝采用在加壓室內燃燒甲烷氣體的方法，通過氧化反應從加工過的零件上去除毛刺、毛邊或隱藏的污染物。那么您知道高壓去毛刺清洗機的日常維護是怎樣的嗎？

The high-pressure deburring and cleaning machine process uses the method of burning methane gas in the pressurized chamber to remove burrs, burrs or hidden pollutants from the processed parts through oxidation reaction. Do you know how the daily maintenance of the high-pressure deburring cleaning machine is?

1.保持設備放置通風、干燥、潔凈場地，有利于設備的長期高效運轉和使用壽命；

1. Keep the equipment in a ventilated, dry and clean place, which is conducive to the long-term efficient operation and service life of the equipment;

2.使用前務必一定請仔細閱讀說明書；

2. Please read the instructions carefully before use;

3.電源：使用合符設備規格的電源及電源線，用戶方需裝設專用于清洗機的空氣開關；并定期測試電源；

3. Power supply: use the power supply and power cord that meet the equipment specifications, and the user needs to install the air switch specially used for the cleaning machine; And regularly test the power supply;

4.電氣控制箱及相關電氣組件及設備通風口等注意防水，并遠離水蒸汽、腐蝕性氣體、粉塵等；定期用壓縮空氣清理附著的灰塵；

4. The electrical control box and relevant electrical components and equipment vents shall be waterproof and kept away from water vapor, corrosive gas and dust; Clean the attached dust with compressed air regularly;

5.設備長期不用時，請放出洗凈液，干燥內槽及表面后，做好防塵和防潮工作，并拔下電源插頭

5. When the equipment is not used for a long time, please release the cleaning liquid, dry the inner tank and surface, do a good job in dust and moisture prevention, and unplug the power plug

6.洗凈槽中無液或液位不足都會對設備造成不可逆損傷；

6. No liquid or insufficient liquid level in the washing tank will cause irreversible damage to the equipment;

7.要清洗的工件應放在洗籃中清洗，禁止直接放在清洗槽內；

7. The workpiece to be cleaned should be placed in the washing basket for cleaning, and it is prohibited to put it directly in the washing tank;

8.定期測試設備的絕緣性能；定期檢查易老化電氣組件；定期檢查傳動部位螺栓，緊固電柜內線頭固定螺栓，及各部分緊固螺栓等；

8. Regularly test the insulation performance of the equipment; Regularly check the aging electrical components; Regularly check the bolts of the transmission parts, fasten the fixing bolts of the wire head in the electric cabinet and the fastening bolts of each part;

9.山東超聲波清洗機設備帶有過濾裝置的，應定期更換過濾芯；清洗機配件帶有傳動機構的，應定期加注機油、黃油等潤滑劑，定期更換減速機齒輪油；

9. If Shandong ultrasonic cleaner equipment is equipped with filter device, the filter element shall be replaced regularly; If the parts of the cleaning machine are equipped with a transmission mechanism, oil, butter and other lubricants shall be regularly filled, and the gear oil of the reducer shall be regularly replaced;

10.長時工作的清洗機，在停機前，風機需再工作3～6分鐘后關機，以保證電源內部熱量散出；

10. For the long-time cleaning machine, before shutdown, the fan shall be shut down after 3-6 minutes of operation to ensure that the heat inside the power supply is released;

11.清洗液應及時沉淀、過濾或更換；定期清理儲油箱被污染的清洗液；定期讓油泵運轉一次，每次至少在10min以上。

11. The cleaning solution shall be precipitated, filtered or replaced in time; Regularly clean the contaminated cleaning liquid in the oil storage tank; The oil pump shall be operated regularly for at least 10min each time.

注意：將每個需要去毛刺或毛邊的零件松散地放在專用籃內（非關鍵部件），或固定在一塊板子內，然后放入燃燒室進行加工。期間要使用正確的操作方式才行，更多相關內容就來我們網站m.chendakeji.cn咨詢看看吧。

Note: each part requiring deburring or burring shall be loosely placed in a special basket (non key part) or fixed in a plate, and then placed into the combustion chamber for processing. During this period, you should use the correct operation mode. For more information, please visit our website m.chendakeji.cn.